I've just purchased and deployed these to my BMG, tolerances are great and the end product is very high quality, would definitely recommend to anyone looking to replace these parts at some point!
great color!
By far the best Snapmaker u1 buildplate! I am 30 prints in and loving it.
Just great! makes for good fossils prints.
I really like this filament. It is easy to print with and yields awesome professional looking results. It does seem that the colors in the pictures do not quite match the printed result. The Cardovan in the image looks much lighter and more red/pink the printed result which is darker and more purple. Maybe this is the light or maybe my model, but it was a bit unexpected. Now I know
this build plate had been doing great out of the box
This was just to treat myself...got a project in mind for it.
but that can be fixed with the dual handle mod on printables. then it seals waaay better
but golly does this thing kick butt. it takes like 15000 samples for a bed mesh in ~10 seconds. has proximity and contact probing. totally worth it
this thing is awesome. was trying to pluck my belts like a caveman with 69 diff apps open. can get all 6 of my belts correctly tensioned in less than 5 mins with this. highly recommended!
Wanted a replacement for GDS time fan. A really great fan, using it on my stealth burner. Lots of cooling and the Tachometer is great for remote monitoring.
Nice build plate, with a smooth finish for prints. I've only used PETG so far, and always wash with IPA, followed by a release product (3DLAC). No issues with adhesion, and after cooling, prints pop right off.
Double sided, so even sweeter!
Great as expecter
I have an A1 and I print mainly PLA and PETG this plate is great. I had some issues with large flat prints lifting even with a brim this has solved that and the surface textures is pleasant. Would recommend it.
The fans are very quiet
Great pushing force, and can still hit high acceleration and controlled pressure advance
Hard to find closed loop 9mm belts at a reasonable price. These work great, just wish they had 10mm belts too.
Works great, they have aluminum spacers. Which would actually make it high temp resistant, unlike the omc or 2nd gen kraken motors that have plastic spacers that melt and cause issues.
Purchased this to replace an LDO Voron kit plate that got a hole ripped out of the surface. PEI side works well with ABS, although it's not quite as sticky as the old LDO plate. I have not had much luck getting the PEO side to work with PLA.
Love WEST3D. simply the best
Plate looked wonderful after unboxed, but that turned out to be short lived. I was tuning Flow Ratio on Fiberon PA612-CF with the YOLO coarse pattern in OrcaSlicer as the very first (and only) print on this rather spendy plate. As soon as it cooled off (~1 hr +/-) I realized that there was going to be an issue. None of the tabs would release. At all. No amount of flexing, picking, or cussing would get my test tabs to release. I finally had to resort to force. I broke out the Panda Printer bed scraper. As I worked my way around the edges, I started to realize that I was experiencing a rather serious case of buyer's remorse. The further I got in removing the test tabs the more horrifying the evidence of permanent damage became. EVERY SINGLE SPOT where there was a tab, the Garolite was lifted off of the flex plate. Each tab took some of the plate surface off of the Garolite, exposing the fiberglass core underneath.
So the plate is ruined,
I do not have these kind of issues on my Etsy sourced G10 plate.
Polymaker Fiberon PA612-CF @ 300c
Bed temp-100c
Camber 60c
Printing YOLO Pass1 Coarse Flow Ratio Test from OrcaSlicer Calibration tab.
Cooled to room temp before removal (attempted removal, anyway)
I've contacted West3D about this issue and will update review regarding resolution.
Sadly, at this time, I can NOT recommend this product for my use case, engineering type technical filaments.
Purchased this to replace my moons dead stepper. Same performance as moons IMO. Does run a bit warmer so you will likely have to adjust to adjust your run current
Bought some 24v 5015’s for my ender 3 pro to improve print quality. Originally bought cheap amazon 5015’s, but they vibrated like crazy resulting in artifacts in my print walls. So got these Sunon ones. Parts got shipped within a day, had them in hand in 4-5 days. Got a thank you note and a little candy with them too. Fans working great, quiet & super strong. Glad I didn’t have to bother with getting them shipped from China, and at a fair price. Would recommend.
This is my first time using 1.5 belts but they are increadibly smooth. As for any gates product they are also durable.
