I installed this with a pi5 in a heavily modified SV08 that I will be adding INDX to when my kit arrives. The leviathan is easy to set up, flash etc.
This is my second BTT touchscreen. They are easy to install, bright touchscreen is sensitive enough for me.
I installed this in an SV08 I'm modifying with new mainboard, pi, display etc. I'm using all three 24V DC outputs for various items. Not mutch time on it yet, but smooth sailing so far.
Other than some very light soldering, this was a very quick and easy build.
Got it done in a week!
The Github repo for this project is a bit of a mess, with mislabeled files and parts. But this kit does give you everything you need. In my case, the fastener heads wouldn't fit the countersinks in the parts, so I redesigned them. I believe this is fixed, now. Once installed, it's a very satisfying door. Probably in the top 3 mods on my V0.2.
Used these to install the 'beefy front idlers' on my Voron Trident, and they worked perfectly. Size as described.
This is great filament. I used to use a lot of Polymaker ASA, but I get the same quality from Ambrosia and it's slightly less expensive. Also the color offerings are better!
These fit the bill better than the generic ones from amazon
An exact replacement. Fit and finish might even be better than stock. I do wish it came with the torx grub screws like the original instead of hex, but they work.
I was worried about calibration differences from the stock thermistor but I don't believe there are any. All profiles print great still. Fits perfectly and the perfect length.
Works perfectly and fit the heat block and plug fine. The harness is just a little long. Better than being too short but it makes tucking the wire in neatly a little harder.
works as advertised.
The sparkles in all of the colors I have bought are striking and reflective, especially the multi-color in the supernova black.
The cosmic shimmer color is also a must-try, it is slightly translucent which is hard to see in the product, photos, but it can be used to make some really cool effects when printed in thin sheets.
Like other Ambrosia I've used, I had to increase my extrusion multiplier just slightly on my Prusa MK3.5s w/ REVO. However, after that it prints flawless. Best price/performance filament and a great middle ground between Amazon-special filament and boutique american/european made filaments.
Amazing and economic upgrade for the Prusa MK3 series. Massive improvement over the V6 and the quick nozzle changes really make it easy to fine tune your printer for each job in basically seconds.
Note that while the MK3/S/+ has firmware that supports the 60W heater, the MK3.5/S does NOT. And only supports the 40W heatercore.
My only gripe is I wish we had the option to substitute the brass nozzles for obxidians with the 40mm heatcore set (for an upcharge of course). A small gripe and nothing to do with the product at all.
Titanium Anno and the Cool Pearl are some of the most beautiful and unique filaments that I have used. I can't wait to try the rest of the color lineup.
The color shifting properties creates some really cool effects when used with non-standard top layer patterns, and they look incredible when printed in thin-wall features, especially the pearl, which is ever so slightly translucent when printed in low wall counts.
Last but not least, the filament looks incredible in natural light/the sun.
Pictures really do not do this stuff justice, you won't be disappointed!
My only complaint about this PETG from west is the lack of colors compared to all of their other offerings. I would love to see more colors and translucent PETG (where PETG really shines IMHO).
That said, if the colors that are available fit your project, this is a great printing PETG and so far one of if not the best I have found in terms of price-performance.
I had to bump up my extrusion multipler slightly for my Prusa MK3.5S, just from 1 to 1.01.
Printed beautifully at 240C. Slow down external perimeters and top layers for best results!
These nozzles are a big step up from the standard brass nozzles, even if you don’t print any specialty filaments. The DLC coating is very non-stick compared to brass, and gives me a nicer surface finish and much less globbing!
I think these are the best nozzles for the REVO. The diamondback is surely a great nozzle, but you can get an entire four nozzle set of these ObXidian’s for the cost of a single DiamondBack…which makes the Diamondbacks a bit of a non-starter to me. These are definitely worth it over the brass nozzles though, in my opinion.
Even normal filament will gradually wear out brass, especially white hues!
Finally took the dive to see what others were talking about with the Beacon mod for the Plus 4. My only complaint is that I didn’t do it sooner! Great community help in support of both the hardware install and clear concise instructions for the software changes.
Best part is “It Just Works!”
Thanks to West 3d for the availability when no one else did and for a quick and seamless buying and shipping experience!
These are by far my favorite nozzle for the k2
Ambrosia ASA is hands down my favorite filament.
ASA beats out ABS for a number of reasons which is why I prefer it. PLA I use for prototypes.
Comes in a great selection of colors which all print cleanly and amazingly.
Shipping deal with Ambrosia is icing on the cake and West3D always ships fast. Even better if you live on the west coast. If only all online shops were like West3D.
Believe the hype. Ambrosia ASA is what you want.
